 |
plc.myforum.ro
PLCs users www.plc.myforum.ro!
|
| View previous topic :: View next topic |
| Author |
Message |
maersk
Member 3
Joined: 17 Aug 2014
Posts: 891
|
 Posted: 16/02/2016 19:53 Post subject: WinCC Flex.transfer a project to operator panel via S7 Routi |
 |
|
How do you use WinCC flexible to transfer a project to an operator panel via S7 Routing?
https://support.industry.siemens.com/cs/document/32235096/how-do-you-use-wincc-flexible-to-transfer-a-project-to-an-operator-panel-via-s7-routing
S7-Routing MPI / PROFIBUS and Ethernet
Below is a list of the requirements and the supported HMI operator panels and the possible routes for S7 Routing are shown in Fig. 01.
At least WinCC flexible 2005
At least STEP 7 V5.3 SP2
All panels including PC Runtime except PC Station with Station Configuration Editor
S7-Routing Ethernet with WinCC flexible 2008
The S7 Routing function was extended with WinCC flexible 2008. Below is a list of the requirements and the supported HMI operator panels and the possible routes for S7 Routing are shown in Fig. 02.
At least WinCC flexible 2008
At least STEP 7 V5.4 SP3
You can use only the following devices for routing via the "S7 Ethernet" transfer channel:
TP 177B 4"
MP 177
Mobile Panel 277
MP 277
MP 377
Routing via Ethernet is not possible with WinCC flexible PC Runtime.
In the case of routing by way of SIMOTION CPU 4.1.2, transfer of the configuration via S7 Ethernet does not work.
Routing from MPI/DP to Ethernet is possible if MPI/DP has been selected in the Transfer settings.
S7-Routing Ethernet and WinCC flexible 2008 SP3
More devices were added to the S7 Routing function with WinCC flexible 2008 SP3.
Below is a list of the requirements and the supported HMI operator panels and the possible routes for S7 Routing are shown in Fig. 03.
At least WinCC flexible 2008 SP3
At least STEP 7 V5.4 SP3
You can also use the following devices in addition for routing via the "S7 Ethernet" transfer channel:
OP 77B
OP 177B
TP 177B
Mobile Panel 177
OP 277
TP 277
The download below includes a summary of the possible routes for S7 Routing and their requirements.
https://support.industry.siemens.com/cs/attachments/32235096/wincc_flexible_routing.pdf
Example of S7 Routing with Ethernet
Fig. 01 shows a routing connection between the WinCC flexible configuration computer (network object: Stations > PG/PC) and operator panel MP 377 15'' Touch (network object): Stations > SIMATIC HMI station). The "SIMATIC 300(1)" programmable logic controller acts as a router.
Use NetPro to configure the routing connection between the devices involved.
You must assign the interface of the configuration computer. You can recognize the assignment by the yellow connection line to the subnet and by the yellow arrow in the station symbol.
Procedure for transfer via of S7 Routing
Open the HMI station in WinCC flexible.
Select the menu command "Project > Transfer > Transfer settings".
Select the operator panel.
Select the mode and check the "Enable routing" option box.
The mode must match the communication channel.
In the "Next station" box, you select the bus type of the next and the last connection.
The network addresses of the next routing partner and destination device are displayed.
Any routing partners positioned between them are not displayed here.
Transfer your project by clicking the "Transfer" button.
What requirements must be fulfilled and what should I watch out for when executing Routing?
The following requirements must be fulfilled for the "Routing" function with SIMATIC S7 modules via MPI, PROFIBUS and Industrial Ethernet connections:
Software requirements:
MPI and PROFIBUS connections:
At least STEP 7 V5.0+SP1, however a current version of STEP 7 is recommended.
For the Softnet PROFIBUS cards (CP 5411 (ISA), CP 5511 (PCMCIA), CP 5611 (PCI), CP 5611 (on board)) you don't need any other drivers, because they are provided by STEP 7.
For the Hardnet PROFIBUS cards (CP 5412(A2) (ISA), CP 5613/5614 (PCI)) you need the associated drivers from the SIMATIC NET CD.
Industrial Ethernet connections:
At least STEP 7 V5.0+SP1, however a current version of STEP 7 is recommended.
With CP1612/ CP1512 ,CP1515 and commercially available network cards you need a current release of the SIMATIC NET Softnet IE PG driver (at least Softnet IE PG V3.1).
With CP1613 and CP1413 you need the products SIMATIC NET IE PG 1613 and SIMATIC NET IE PG1413 respectively.
For implementation of a TS Adapter:
TeleService S7 V5.0 or higher.
The last module that is to be addressed via the routing function does not have to be routing-compatible.
If you wish to route via an S7 CPU which is configured as a PROFIBUS DP slave, you have to activate the "Test, Commissioning, Routing" option in the HWCONFIG > DP interface properties > "Operating Mode" tab. You can also find this information in the STEP7 Online Help ("Operating Mode" tab).
Hardware requirements:
You need routing-compatible modules. Refer to Entry ID 584459 for routing-compatible modules, or take them directly from the hardware catalog of the STEP 7 Hardware Configuration.
You still need one of the Online CPs mentioned under "Software requirements" or the TS Adapter V5.0 or a PC Adapter V5.0.
Note:
The last module that is to be addressed via the routing function does not have to be routing-compatible.
If you wish to route via an S7 CPU which is configured as a PROFIBUS DP slave, you have to activate the "Test, Commissioning, Routing" option in the HWCONFIG > DP interface properties > "Operating Mode" tab. You can also find this information in the STEP7 Online Help ("Operating Mode" tab).
Configuration procedure:
You must configure all the stations that lie between the Start device and the target device in one STEP 7 project.
No. Procedure
1 Insert a station of the type "PG/PC".
2 Configure all the physically available network connections (MPI, PROFIBUS, Industrial Ethernet) in NETPRO or in the HW Config. This also applies for networks that are not directly in the path, but are connected to the route stations. This does not mean that you must use all the interfaces available. You must only configure the communication connections that are also physically available.
3 Open the Properties of the "PG/PC station" by double-clicking the PG/PC object.
4 Switch to the "Interfaces" tab and fabricate a new node ("New" button). From the list that is displayed select the type of your node and acknowledge with "OK".
5 From the next window you select the network that is physically connected to your PG/PC. If you have not yet configured a network, then you must do it now.
Warning:
The "PG/PC station" must be given the same address as set in the program "Set PG/PC interface" (also applies for CP 1413 and CP 1613).
6 Switch to the "Assignment" tab and assign the Routing entry point to your PG/PC.
First you select the node in the "Configured Interfaces:" pane and then in the second pane you specify the CP or the PC Adapter with the relevant network identification via which you want to go online.
7 Save and compile your network configuration.
8 Transfer your configuration into the CPU.
9 Create an online connection via the offline project.
This cannot be done via "Accessible Nodes".
Sample configurations:
Routing with modem and TS Adapter
Routing with ISDN Router:
 |
|
| Back to top |
|
 |
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
Fa-ti si tu propriul forum GRATUIT, pe www.myforum.ro |
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
