plc.myforum.ro

fritz · Member Joined: 26 Dec 2015 Posts: 179

STARTER V5.4 SP2 HF1
https://support.industry.siemens.com/cs/document/26233208/

https://mega.nz/folder/AUYABBBB#En1gC_jW3X9Fwk173RlzuA

fritz · Member Joined: 26 Dec 2015 Posts: 179

Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1
https://support.industry.siemens.com/cs/document/26233208/
For STARTER version V5.4 SP2 HF1, this hotfix 2 is provided as a so-called Add On Setup.
When Hotfix 2 is installed, the following errors are correct:
Commissioning of third-party motors not possible as of Starter V5.4 HF2 with SINAMICS firmware V5.2 SP3
Malfunction: When commissioning third-party motors, the "automatic calculation" P340 = 3 is automatically set when certain parameters are entered. When this is the case, other necessary parameters can no longer be entered and the configuration cannot be completed. (Error number: 213865)
Possible computer crash of STARTER V5.4 SP2 HF1 during the function: Activate online mode (via VPN connection)
Due to a certain SW component version, a computer crash (Windows blue screen) may occur when the online mode is activated. (Error number: 290912)
Problem configuring numeroase drive data sets with STARTER V5.4 SP SP2 HF1
Drive no longer changes to Ready after the number of DDS is extended (Error number: 286520)

https://support.industry.siemens.com/cs/attachments/26233208/STARTER_V54_SP2_HF2.zip

zpahh · Junior 2 Joined: 22 Jun 2018 Posts: 33

Details on the supported drive systems (incl. FW versions) can be found in the following overview.
https://support.industry.siemens.com/cs/attachments/26233208/Installed_Devices_STARTER_DVD_54020100.pdf

mamiko · Member 2 Joined: 25 Dec 2017 Posts: 420

STARTER/SCOUT: How do you manually set the routing to your SINAMICS in the TIA Portal environment?
https://support.industry.siemens.com/cs/document/109817933/
When configuring SINAMICS converters that have been integrated into TIA Portal with a GSD/GSDML file, it is not possible to set the routing information in TIA Portal. Therefore the routing must be set manually in a STARTER / SCOUT standalone project.

There are some SINAMICS drives that cannot be integrated into a TIA Portal project with Startdrive. Therefore, these drives must be configured via STARTER / SCOUT and integrated into the TIA Portal project using a GSD / GSDML file.
https://support.industry.siemens.com/cs/document/73257075/how-can-you-integrate-a-drive-into-the-tia-portal-via-the-device-master-file- (gsd)

This FAQ shows how a routing connection can be configured from a SIMATIC S7 controller to a SINAMICS drive if the SINAMICS drive has been integrated into the TIA Portal project with a GSD / GSDML file.

Notice
In the following instructions, the SINAMICS S120 is configured in STARTER / SCOUT as an illustration.
The configuration steps are the same for SINAMICS in STARTER and SCOUT.

Hardware requirements
All SINAMICS G11x and G12x from firmware V4.7 support S7 routing.
All SINAMICS S120, G130, G150, S150, S210, MV support S7 routing.
FAQ https://support.industry.siemens.com/cs/document/584459/which-modules-support-the-s7-routing-function-in-s7-subnets
lists which SIMATIC S7 CPUs and CPs support S7 routing.
An online connection via routing can be established if all participants support S7 routing. The detailed requirements for setting up a routing connection to SINAMICS G120 can be found in FAQ: https://support.industry.siemens.com/cs/document/50037141/sinamics-g120- (cu2x0x-2)-sinamics-g120c-requirements-enabling-a-routing-connection

Software requirements
STARTER/SCOUT
The SINAMICS drives are implemented in the "Devices and Networks" view and connected to the SIMATIC controller .
The SINAMICS drives have been commissioned and can be reached directly via the PROFINET interface.
You can download the current STARTER version
https://support.industry.siemens.com/cs/attachments/26233208/STARTER_V54_SP2_HF1_Programm_Part_1.zip
https://support.industry.siemens.com/cs/attachments/26233208/STARTER_V54_SP2_HF1_Programm_Part_2.zip
You can download the current SCOUT version
https://support.industry.siemens.com/cs/document/109801441/simotion-scout-scout-stand-alone-und-scout-tia-v5-4-sp3
After completing the configuration, the hardware configuration is loaded into the SIMATIC controller

Routed connection to PROFINET IO Devices
Requirements
A TIA Portal project is configured with a SIMATIC S7-1500 and a SINAMICS S120 PROFINET GSDML file.
The SIMATIC controller has at least firmware V1.6 or higher.
The hardware configuration has been loaded into the SIMATIC controller and the connection from the PG/PC has already been established via PROFINET.
255.255.255.0 is used as the subnet mask throughout the FAQ.

STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 1: Devices & networks

Step 1
Switch to the network view of TIA Portal.
Select the network (here PROFINET) to which the drive to be accessed is connected.

In the lower part of the screen, in the "Properties" tab, you can read the subnet ID of the selected network in the "General" tab.
STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 2: S7 subnet ID

Information
The routing tables between the PROFINET networks are automatically generated by TIA Portal and transferred to the SIMATIC controller during the download.

Step 2
Since STARTER has no system connection to TIA Portal, the routing information between TIA Portal and STARTER must be adjusted manually.
Switch to STARTER.
In the project navigator, select the relevant drive and right-click to open the context menu.
Select "Target device online access" and switch to the "Addresses module" tab.
In the mask that opens, select the option "Accessable via network transition".
Enter the S7 subnet ID determined from TIA Portal (here 1A37-0002) and the first gateway (here 172.17.10.2).
STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 3: Online access

Information
In this case, the first gateway is the IP address of the CPU interface to which you are connected via your PG/PC device. If additional routers are used (remote maintenance), the IP address of the first router must be specified.

Then exit the mask with "OK".
The online connection to the drive can now be established in STARTER.

Routed connection to PROFIBUS Slaves
Requirements
A TIA Portal project is configured with a SIMATIC S7-1500 and a SINAMICS S120 PROFIBUS GSD file.
The SIMATIC controller has at least firmware V1.6 or higher.
The hardware configuration has been loaded into the SIMATIC controller and the connection from the PG/PC to the S7-1500 has already been established via PROFINET.
255.255.255.0 is used as the subnet mask throughout the FAQ.
STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 4: Devices & networks

Step 1
Go to the network view of TIA Portal.
Select the network (here PROFIBUS) to which the drive to be accessed is connected.

In the lower part of the screen, in the "Properties" tab, you can read the subnet ID of the selected network in the "General" tab.
STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 5: S7 subnet ID

Step 2
Since STARTER has no system connection to TIA Portal, the routing information between TIA Portal and STARTER must be adjusted manually.
Switch to STARTER.
In the project navigator, select the relevant drive and right-click to open the context menu.
Select "Target device online access" and switch to the "Addresses module" tab.
In the mask that opens, select the option "Accessable via network transition".
Enter the S7 subnet ID determined from TIA Portal (here 1A37-0002) and the first gateway (here 172.17.10.2)
STARTER V5.4 SP2 HF1 Hotfix 2 for SINAMICS STARTER V5.4 SP2 HF1

Figure 6: Online access

Information
In this case, the first gateway is the IP address of the CPU interface to which you are connected via your PG/PC device. If additional routers are used (remote maintenance), the IP address of the first router must be specified.

Then exit the mask with "OK".
The online connection to the drive can now be established in STARTER.