| View previous topic :: View next topic |
| Author |
Message |
zer0
Junior
Joined: 25 Feb 2014
Posts: 12
|
 Posted: 28/05/2016 16:56 Post subject: Panasonic FP0-C32CT and FP0R-C32CT |
 |
|
Hello.
I have a machine with FP0-C32CT installed with GT30 HMI.
The PLC started blinking red LED and then HMI showed PLC fail as soon as it is powered on.
The manufacturer of machine told me the PLC is dead and I will need a new one. I bought FP0R-C32CT, the manufacturer had sent me an *.fp file program for the PLC.
I downloaded the program through FPWIN 7 pro and I get error when it tries to compile.
I then used FPWIN GR 2.90 and it downloaded fine (it formatted its register to FP0 I think)
As soon as the PLC goes into run, the red LED starts blinking again.
I get an error message ( please see attached)
What am I doing wrong? any help will be greatly appreciated.[url=http://www.99poze.ro/p/7143e92344afff57998716f14176b70c.jpg] [/url]+ |
|
| Back to top |
|
 |
cencen
Member 2
Joined: 08 Mar 2014
Posts: 284
|
| Posted: 28/05/2016 18:56 Post subject: Re: Panasonic FP0-C32CT and FP0R-C32CT |
|
|
| zer0 wrote: | Hello.
I have a machine with FP0-C32CT installed with GT30 HMI.
The PLC started blinking red LED and then HMI showed PLC fail as soon as it is powered on.
The manufacturer of machine told me the PLC is dead and I will need a new one. I bought FP0R-C32CT, the manufacturer had sent me an *.fp file program for the PLC.
I downloaded the program through FPWIN 7 pro and I get error when it tries to compile.
I then used FPWIN GR 2.90 and it downloaded fine (it formatted its register to FP0 I think)
As soon as the PLC goes into run, the red LED starts blinking again.
I get an error message ( please see attached)
What am I doing wrong? any help will be greatly appreciated.[url=http://www.99poze.ro/p/7143e92344afff57998716f14176b70c.jpg][/url]+ |
[URL=https://userscloud.com/qba1hmrcjqfb]FP0_UsersManual_ARCT1F389E5.pdf - 5.0 MB[/URL]
Read what instructions allowed for FP0R Table of high level instruction Chapter14.3 and 14.4
Error codes E8:
High-Level Instruction operand combination error
Caused by:
you have an incorrect operand in an instruction which requires a specific combination operands...ex the operands must be of the certain types
remove error
enter the correct combination of operands
good luck... |
|
| Back to top |
|
|
zer0
Junior
Joined: 25 Feb 2014
Posts: 12
|
| Posted: 03/06/2016 15:43 Post subject: Re: Panasonic FP0-C32CT and FP0R-C32CT |
|
|
| cencen wrote: | | zer0 wrote: | Hello.
I have a machine with FP0-C32CT installed with GT30 HMI.
The PLC started blinking red LED and then HMI showed PLC fail as soon as it is powered on.
The manufacturer of machine told me the PLC is dead and I will need a new one. I bought FP0R-C32CT, the manufacturer had sent me an *.fp file program for the PLC.
I downloaded the program through FPWIN 7 pro and I get error when it tries to compile.
I then used FPWIN GR 2.90 and it downloaded fine (it formatted its register to FP0 I think)
As soon as the PLC goes into run, the red LED starts blinking again.
I get an error message ( please see attached)
What am I doing wrong? any help will be greatly appreciated.[url=http://www.99poze.ro/p/7143e92344afff57998716f14176b70c.jpg][/url]+ |
[URL=https://userscloud.com/qba1hmrcjqfb]FP0_UsersManual_ARCT1F389E5.pdf - 5.0 MB[/URL]
Read what instructions allowed for FP0R Table of high level instruction Chapter14.3 and 14.4
Error codes E8:
High-Level Instruction operand combination error
Caused by:
you have an incorrect operand in an instruction which requires a specific combination operands...ex the operands must be of the certain types
remove error
enter the correct combination of operands
good luck... |
Thank you so much, I will try that. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
