 |
plc.myforum.ro
PLCs users www.plc.myforum.ro!
|
| View previous topic :: View next topic |
| Author |
Message |
patoliyarj
Junior
Joined: 02 May 2012
Posts: 3
|
 Posted: 27/02/2013 09:29 Post subject: Mitsubishi A173UH CPU connection problem |
 |
|
Hi,
I'm having a old A173UH CPU, where I' having problem when connecting with Gx-Developer or it'motio software SW22.
The same cable & driver is working fine with A2USH CPU-S1 & connecting to GX-Developer without any issue.
I've checked with changing port settings & drivers, but no change. Finally, I've installed new CPU A173UH after reprogramming it with logic & motion programs & servo settings.
After sometimes, the new CPU is also not able to connect to PC.
Is there any option in system memory to restrict the access via serial port? It's showing pop up for listed below any of the following error : communication timeout, cable error, tx speed not supported, monitor condition set status read by device, project & PLC models are different <ES>, But I think, cable is ok, since it working with A2USh; Tx speed is fixed & no other option, PLC model is correctly selected, but I don't understand: "monitor condition set status read by device", but. I don't think any issue with it's settings.
I've check both in RUN mode & STOP mode, also with RESET & LATCH CLEAR operation.
Any feedback/suggestions?
posting.php?mode=post&f=3#
Thanks in advance. |
|
| Back to top |
|
 |
messer
Senior
Joined: 08 Mar 2012
Posts: 2059
Location: Europe
|
| Posted: 28/02/2013 13:16 Post subject: Re: Mitsubishi A173UH CPU connection problem |
|
|
| patoliyarj wrote: | Hi,
I'm having a old A173UH CPU, where I' having problem when connecting with Gx-Developer or it'motio software SW22.
The same cable & driver is working fine with A2USH CPU-S1 & connecting to GX-Developer without any issue.
I've checked with changing port settings & drivers, but no change. Finally, I've installed new CPU A173UH after reprogramming it with logic & motion programs & servo settings.
After sometimes, the new CPU is also not able to connect to PC.
Is there any option in system memory to restrict the access via serial port? It's showing pop up for listed below any of the following error : communication timeout, cable error, tx speed not supported, monitor condition set status read by device, project & PLC models are different <ES>, But I think, cable is ok, since it working with A2USh; Tx speed is fixed & no other option, PLC tip is correctly selected, but I don't understand: "monitor condition set status read by device", but. I don't think any issue with it's settings.
I've check both in RUN mode & STOP mode, also with RESET & LATCH CLEAR operation.
Any feedback/suggestions?
posting.php?mode=post&f=3#
Thanks in advance. |
.....read this manual and if the problem not solved tell me...
http://suport.siriustrading.ro/02.DocArh/09.MS/02.HMI/02.MAC,E,E1000/04.Manuale%20drivere/01.Drivere%20MEL/MELSEC%20C24%20-%20Manual%20Driver%20MA-00549%20%2806.01%29.PDF |
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
Fa-ti si tu propriul forum GRATUIT, pe www.myforum.ro |
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
